| Waterbed Heaters |  |
How to use the Thermal Guardian Ener-Save Safe Heater Safely! Waterbed heaters for both traditional hardside and softside beds have been improved recently with safety and comfort advances. These advances affect some of the installation and use conditions of theh eaters and must be addressed before your new heater is installed. The new motionless water mattresses have also contributed to the heater advances. These new mattress designs have increased fiber filling in the mattress interior to the degree that the water is virtually trapped and almost no water circulation occurs. One of the safety advances is lowering the operating temperature of the heater pad when it is working. The addition of a sensitive fuse in the pad is another safety improvement keeping the pad from ever reaching too hot of a temperature. The next section will provide you with some important tips on the proper heater installation to give you the maximum enjoyment of your sleep environment. Never plug in the heating unit until the mattress is completely filled with water. The Thermal Guardian® Temperature Control Systems are designed with your safety as our number one concern. Each heating pad is engineered to shut down in the event of an overheating situation. Under normal use, this is an outstanding feature; however, if the pad is heated without the proper depth of fluid to whisk the heat away, the safety fuse can trip which renders the pad unable to operate. Some models of the Thermal Guardian® heating pads are rolled at the factory. The proper method of flattening the pad is done by using the reverse roll. Do not heat the pad, as this may cause the safety fuse to trip. To ensure proper enjoyment of your new flotation sleep system, always fill the mattress with warm water. This can be done using a faucet adaptor attached to any kitchen or bathroom sink. The use of a cold water fill will prolong the warm up time. The Ener-Save design allows the pad to raise the temperature of the water at the approximate rate of _ to _ degree Fahrenheit per hour. Assuming a cold tap temperature of 45 degrees, this will bring the bed to a comfortable sleeping temperature in 5-7 days. To avoid this delay, the warm water fill can provide you a great night’s sleep on the very first night. If your hot water tank is drained during the fill process, simply turn off the water supply and wait approximately 30-45 minutes. The mattress should be filled to within approximately 1” below level with the frame. It is always easier to add a few pitchers of water to create a less-supportive feel, than it is to drain an overfilled mattress. Once the mattress is filled, it is recommended that no adjustment be made for 7-10 days to allow the body to adjust to the new support system.
Open the fill valve on the mattress and inflate it with air until it is about 2 feet tall.Replace the cap and pushdown on the center of the expanded mattress to force the wrinkles from the bottom of the mattress which will help prevent issues with the heater pad. This also allows you to center the mattress easily in the frame as you release the air from the mattress and prepare for a warm water fill. By centering the mattress with air you will ensure a comfortable fit and a great night’s rest for years to come. Periodic conditioning of the inside and outside of your vinyl water mattress will improve your overallenjoyment and provide a more comfortable night’s sleep.Upon finishing the initial fill of your mattress, place8 ounces of a Fiber Bed waterbed conditioner inside the chamber (for Dual chambers add 4 ounces to each side).This will adequately treat the water (for well water it is recommended to double this dosage) for one year. Theconditioner prevents algae growth in the water, which in turn minimizes air bubbles. It also lubricates the inside ofthe vinyl to keep it soft and supple. To create the same level of protection on the outside of the mattress, the useof a Waterbed Vinyl Conditioning spray will remove body oils which if left unattended, can cause the vinyl tobecome brittle. Cleaning the surface bi-monthly will help prolong the life of the mattress and enhance the comfort. Plug in your heater and enjoy your warm waterbed!
|
Proper placement of the heater during installation is critical to the long life and enjoyment of your Thermal Guardian® Temperature Control system. The heater pad must be positioned upon a rigid surface without any foreign material, such as blankets or sheet, coming in contact with the pad. Never place the pad over any crack sor imperfections in the foundation or decking. The pad must be directly underneath the safety liner. The black temperature sensor should be a minimum of 12” from the pad and 6” from the sides of the bed to provide accurate temperature readings. The mattress is then placed on the liner, inside of the frame perimeter. 